Hot Selling for Elbow 45° to Zurich Factories

Hot Selling for Elbow 45° to Zurich Factories

Short Description:


Product Detail

Production detail

Product Tags

Related Video

Feedback (2)

, , ,
Hot Selling for Elbow 45° to Zurich Factories Detail:

Table sizes of Elbow 45°:

American-Standard-Malleable-Iron-Pipe-Fittings美标-8_50

Specification of Elbow 45° : 

111 The equipement from DISA Denmark, DJ AMF Japan, SINTOKOGIO Japan widely used in our malleable iron elbow productline, ensures the stability of product quality.
We use spectrometer from Oxford Instruments to check the material’s quality. 未标题-1_05
未标题-1_07 We use high heat value natural gas annealing furnace, strictly control the annealing process, improve the physical properties of the materials.
We use close-grained, high strength, impeccable steel & plate scrap as the raw material, because the quality of the steel is the starting point of the fittings of excellent quality. 未标题-1_09
螺纹 Accurate threads are processed that comply with the precise standards, such as ASME, EU, BS, DIN, etc. The threads have an accurate structure, so the thread length and straightness to allow them to easily engage threaded pipe.
The pipe fittings have outlets ranging from 1/8” through 8”. 未标题-1_16
压扁 Good toughness with long working life.
Smooth surface without any sand hole. 未标题-1_18
镀锌  avg. thickness of zinc coating is higher than 86 um specified in ASME, EN(70um), DIN(70um), SI(78um).

 

 


Product detail pictures:

Hot Selling for Elbow 45° to Zurich Factories detail pictures


Related Product Guide:
Benefits of Brass Ball Valves
How to Reverse Wrinkled Elbows

Hot Selling for Elbow 45° to Zurich Factories, The product will supply to all over the world, such as: , , ,

PN95口罩详情页



  • VQ35 motors PCV system have been found to suck oil into intake
    manifold. When engine is modified to make more power the increased crankcase pressure allows the possibility of more oil getting into intake manifold. Oil sucked into intake manifold will get into combustion chamber causing fuel dilution, increased compression which will increase knock numbers.

    This kit is designed to remove PCV valve, add a breather to right valve cover and cap the port to the intake manifold. A very simple crankcase breather for your N/A built VQ35. This kit will help relieve built up crank case pressure from lightly modified VQ35 motors. Also removing the possibility of oil getting into intake manifold from PCV valve.

    The kit comes with one PI adapter fitting, one -8 straight push lock fitting, one K&N crankcase vent filter and one vacuum cap for the intake manifold port.

    Remove the PCV valve and hose to intake manifold, cap port to intake manifold. Remove the o-ring from the PCV valve and transfer to the PI fitting. Carefully screw breather assembly into valve cover port. When installing fitting into valve cover due note threads are very fine and easily cross thread able into valve cover. Valve covers are plastic and fitting should be tighten by hand with low amount of torque.

    PCV valve’s are controlled vacuum leaks for engines. The removal of PCV valve will change the idle speed of the engine and the air fuel ratio. Suggested to perform ECU idle air volume relearning and have tuning of ECU checked.

    FITTING IS FOR OFF ROAD USE AND MAY NOT BE LEGAL IN YOUR STATE.

    FITTING IS NOT A GUARANTEED FIX OF YOUR OIL CONSUMPTION.

    This fitting can be purchased on our website at:

    https://projectimport.com/store/350z-g35-oil-consumption-fix-vq35de-and-revup-nissan-infiniti-pcv-valve-delete-and-right-valve-cover-breather-kit/


    5 Stars By from -

    5 Stars By from -

    Related Products

    WhatsApp Online Chat !